The CK0618 Mini CNC Lathe Machine is a compact CNC turning platform identified in the supplied product information as model CK0618. It is configured around a 180 mm maximum swing over bed and a 300 mm maximum workpiece length. For workshops comparing a compact turning solution, the CK0618 Mini CNC Lathe Machine presents the essential dimensions, spindle range, threading ranges and travel values in one documented configuration. The supplied listing also identifies a 20 mm spindle bore, MT3 spindle taper and a four-position electric toolpost.
From a mechanical-planning perspective, a CK0618 Mini CNC Lathe Machine should be evaluated against the actual workpiece envelope, fixture arrangement, tooling and required machining sequence. Published dimensions are a starting point rather than a substitute for confirming your own part drawing and process. This is especially important when evaluating a machine for prototype parts, sample work or model processing, where chucking and tool clearance can influence the usable setup.
The stated maximum swing over bed for the CK0618 Mini CNC Lathe Machine is 180 mm. The supplied specification also lists maximum swing over carriage as 300/350 mm and a maximum workpiece length of 300 mm. These figures help define the physical envelope to check before purchase. The machine uses a 20 mm spindle bore and an MT3 spindle taper. An MT2 tailstock taper is listed, with a 20 mm tailstock diameter and 50 mm tailstock travel.
Its spindle-speed range is specified as 50–2250 rpm. Higher speed is not automatically the best choice for every turning job: cutting conditions, workholding, material, tool geometry and stability all matter. If your project requires a particular finish or cycle time, confirm the intended material and cutting process with the supplier rather than treating the speed range as a guarantee of a result. The CK0618 Mini CNC Lathe Machine specification records a 0.001 mm minimum setting unit, but achievable part results remain dependent on setup, tooling, programming and operating conditions.
The CK0618 Mini CNC Lathe Machine is listed with metric thread cutting from 0.5 to 2.5 mm and inch thread cutting from 12 to 52 TPI. This documented range is useful when your drawing calls for supported metric or inch thread pitches. The product information also lists a four-position electric toolpost and an 8 mm gang tool bar size. Together, these facts describe the available tooling arrangement without assuming tooling, controls or accessories beyond the supplied listing.
For a CK0618 Mini CNC Lathe Machine setup, check the practical relationship between the workpiece, chuck, toolholder and tailstock before committing to a process. A parameter table does not show every clearance condition. For example, a small turned component may fit the stated diameter, yet a long part or a particular fixture can change the usable arrangement. That is why a drawing review and a tooling check are sensible steps before ordering.
The supplied data specifies 60 mm X travel and 250 mm Z travel for the CK0618 Mini CNC Lathe Machine. X moving speed is listed as 800 mm/min and Z moving speed as 1200 mm/min. The listed X motor power is 1.5 Nm, and the Z motor power is 2 Nm. The standard spindle motor value is 400 W, with 550 W identified as an optional value. Optional equipment should be confirmed in the quotation and order specification; it should not be assumed to be included with every machine.
These values support a technical discussion, not a complete application study. Feed strategy, tooling, workholding and programming influence machining behavior. Match the documented capacity to the intended part family. A CNC gantry mill is a separate machine category, not an interchangeable turning-machine substitute.
The existing product description identifies precision parts processing, sample processing and model processing as applicable uses for the CK0618 Mini CNC Lathe Machine. Within those general uses, buyers can use the 180 mm swing, 300 mm workpiece length, spindle range and threading ranges as a checklist. Where parts require dimensions or operations outside the published range, ask for a recommended configuration instead of extrapolating from the base specifications.
For a workshop handling small turned samples, the CK0618 Mini CNC Lathe Machine can be considered where the part envelope falls within the stated limits. For thread work, verify the required pitch against the published metric and inch ranges. For repeated work, confirm workholding, tooling, program requirements and any optional motor selection. For brake disc machining cost analysis, use production volume, material removal, tooling, labor and the actual process plan; this product page does not establish a cost figure.
A practical selection process begins with the part drawing. Compare maximum diameter and length with the declared swing and workpiece length. Then identify the required bore, taper, thread pitches and tool positions. Finally, confirm electrical requirements, included accessories, CNC control, installation needs and commercial terms directly with the supplier. The CK0618 Mini CNC Lathe Machine listing provides the documented mechanical starting points, while the final selection should reflect your own process requirements.
| Specification | Listed Value |
|---|---|
| Model | CK0618 |
| Maximum swing over bed | 180 mm |
| Maximum swing over carriage | 300/350 mm |
| Maximum workpiece length | 300 mm |
| Spindle bore | 20 mm |
| Spindle taper | MT3 |
| Spindle speed | 50–2250 rpm |
| Metric thread cutting | 0.5–2.5 mm |
| Inch thread cutting | 12–52 TPI |
| Electric toolpost | 4-position |
| X / Z travel | 60 mm / 250 mm |
| Overall size | 900 × 400 × 1250 mm |
| Net weight | 150 kg |
Before requesting a quote for the CK0618 Mini CNC Lathe Machine, send the workpiece drawing, material, required thread range, expected quantities and preferred options. This helps confirm whether the documented configuration fits your operation. The CK0618 Mini CNC Lathe Machine should be selected for verified requirements, not from speed or size figures alone.












