product-disc-drum-lathe-t8470-for-car-repair-cutting-machine, product-disc-drum-lathe-t8470-for-car-repair-cutting-machine, /auto-maintenance-repair463
EN
This T8470 machine is a workshop machine for machining brake drums and brake discs within the stated model capacity. It gives repair teams a clear set of published operating values to review before installation, tooling selection, and job planning. The T8470 designation, the drum range, disc limit, rotating-speed options, tool travel, variable feed description, motor power, packing dimensions, and gross weight are presented below exactly as available in the product material.
For brake-service work, selection should begin with the actual parts handled by the workshop. The T8470 service lathe lists brake drum processing from 220 to 700 mm and brake disc processing below 550 mm. Those figures are practical screening points, not a substitute for checking the condition, dimensions, and service requirements of each individual part before machining.
Before commissioning, establish a documented routine for cleaning, inspection, secure mounting, tool condition, speed selection, trial cutting, and final measurement. Keep job records with the part identification, measured dimensions, selected setup, and result. These practical controls support consistent workshop decisions while leaving vehicle-specific limits to the applicable service documentation and trained personnel.
Review the manual, local safety requirements, and supplier documentation before installation, operation, maintenance, or adjustment.
| Item | Published value |
|---|---|
| Model | T8470 |
| Brake drum processing diameter | 220–700 mm |
| Brake disc processing diameter | Less than 550 mm |
| Workpiece rotating speed | 30 / 54 / 85 r/min |
| Maximum tool travel | 300 mm |
| Feeding rate | Variable |
| Motor power | 1.5 kW |
| Standard packing dimensions | 1100 × 905 × 1172 mm |
| Gross weight | 600 kg |
These values define the published scope of the T8470 brake machining unit. Confirm incoming power, installation space, compatible fixtures, cutting tools, and required accessories with the supplier before ordering, because the source material identifies standard and optional accessories without a detailed item list.
A common purchasing mistake is to treat the highest available speed as the automatic best setting. For the T8470 equipment, the useful choice depends on the workpiece and process requirements. Qualified operators should set up and inspect each job according to their own approved brake-service procedure.
This T8470 workshop machine is suited to automotive repair and brake-service environments that need a dedicated machine for brake drum and brake disc cutting within the published dimensions. Typical use discussions include vehicle repair workshops, brake-service stations, and equipment distributors specifying a machine for customers whose part sizes fall inside the stated processing limits.
Before a cut is planned, inspect the workpiece and verify its applicable service limits. The product material supports the machine capacities above, but it does not establish the condition or remaining allowable dimension of any particular brake component. Use the vehicle or component manufacturer’s requirements and local workshop procedures for those decisions.
Correct workholding is also important. Many machining issues originate in setup rather than in the machine specification itself. The Disc Drum Lathe T8470 for Car Repair Cutting Machine should therefore be evaluated with the necessary mounting method, tooling, operator training, and inspection process in mind. This is especially relevant where a workshop handles a range of component sizes.
From an engineering perspective, the Disc Drum Lathe T8470 for Car Repair Cutting Machine should be matched to real parts rather than selected from a title alone. Start with the 220–700 mm brake drum range and the less-than-550 mm brake disc limit. Next, review the stated 30/54/85 r/min workpiece speeds, 300 mm maximum tool travel, variable feed description, and 1.5 kW motor against the workshop’s intended tasks.
The supporting phrase mill drill lathe may appear in broad equipment searches, but this T8470 page should be assessed by its stated brake drum and brake disc purpose, not by a generic machine label. Similarly, a hard turning process depends on tooling, material, setup, and process validation that are not specified in this product record. Neither phrase changes the published T8470 specifications.
When receiving a machine, a careful acceptance process is valuable. Record the supplied configuration, confirm that the delivered model and accessories match the agreed order, inspect installation requirements, and conduct commissioning using qualified personnel. The current product material does not list a performance test protocol, certification claim, or accessory inventory, so those items should be clarified before purchase.
For a quotation or configuration discussion, provide the brake drum and brake disc size range you expect to service, the available electrical supply, preferred accessories, installation location, and any packaging or shipping requirements. This allows the supplier to confirm whether the Disc Drum Lathe T8470 for Car Repair Cutting Machine and its available configuration fit the intended operation.
The source content identifies standard accessories and optional accessories, but does not name them. Request the current accessory list, delivery scope, and applicable commercial terms directly. This conservative approach helps buyers compare the complete package rather than assuming equipment or services that are not stated.
In short, the Disc Drum Lathe T8470 for Car Repair Cutting Machine provides a source-documented T8470 option for brake drum and brake disc machining, with 220–700 mm drum capacity, a disc limit below 550 mm, three published workpiece speeds, 300 mm tool travel, variable feed, and a 1.5 kW motor. Confirm final suitability through part measurements, process requirements, and supplier configuration details.




