product-metal-cutting-band-sawing-machine-g5018wa, product-metal-cutting-band-sawing-machine-g5018wa, /metal-cutting-saw
Inquiry
Inquiry

Metal Cutting Band Sawing Machine G5018WA

Request a Quote
  • Overview

Overview

Metal Cutting Band Sawing Machine G5018WA

The Metal Cutting Band Sawing Machine G5018WA is a 750 W, single-phase band saw for metal stock preparation in workshops that need straight and mitre cutting. The G5018WA brings together an adjustable vice, a cast-iron saw frame, a coolant pump, and a sealed worm-and-pinion gearbox drive. It is a practical machine for workpieces that fall within its published cutting capacities. Before choosing any saw, match the workpiece profile, material, required angle, blade, and electrical supply to the job rather than relying on a general feature list.

Cutting Arrangement

The Metal Cutting Band Sawing Machine G5018WA has an adjustable vice for mitre cutting from 90° to 45°, plus a 45° swivel head that allows angle cutting without moving the material. The vice tilt is listed as 0–45°. A material fence assists repeatable stock positioning, while fully adjustable blade rollers are intended to support accurate, straight cutting. These features help organize the setup, but secure clamping and a suitable blade remain essential. For a flat section at an angle, verify that the stock is supported and that the planned cut remains inside the listed 45° capacity.

Cutting pressure can be adjusted to each workpiece, and an adjustable spring-tension screw regulates the feed rate. This gives the operator useful setup control when moving between workpiece shapes or materials. In practical use, a published capacity is a planning limit rather than a guarantee of identical results on every job. Blade condition, correct tension, coolant use, material behavior, and clamping all influence the cut. The cast-iron frame is described as providing vibration-free running, but final cut quality still depends on setup and operating practice.

Published Specifications

Model G5018WA
Motor power 750 W, 1PH
Blade size 2360 x 20 x 0.9 mm
Blade speed at 50 Hz 34 / 41 / 59 / 98 m/min
Blade speed at 60 Hz 41 / 49 / 69 / 120 m/min
90° capacity 180 mm round; 180 x 300 mm flat
45° capacity 110 mm round; 110 x 180 mm flat
Vice tilt 0–45°
Net/gross weight 140 / 170 kg
Packing size 1260 x 460 x 1080 mm
Units per 20-foot container 40 pcs

Features for Workshop Use

  • A V-belt drive provides four speed settings.
  • The stated 50 Hz speeds are 34, 41, 59, and 98 m/min.
  • The stated 60 Hz speeds are 41, 49, 69, and 120 m/min.
  • A coolant pump is included for blade cooling.
  • An automatic cut-off switch is included.
  • A carriage, transport handle, and four wheels help move the machine.
  • The source information states that vertical use is possible for cutting sheet metal.

For a maintenance area or general fabrication shop, the Metal Cutting Band Sawing Machine G5018WA can suit routine cutting of round or flat stock within the documented envelope. At 90°, the listed capacity is 180 mm round or 180 x 300 mm flat. At 45°, it is 110 mm round or 110 x 180 mm flat. A buyer comparing two jobs should consider the actual largest section and the most frequent cut angle, not only the maximum straight-cut number. If the typical stock exceeds these figures, or if the work calls for specialized automation, confirm an alternative configuration rather than assuming it is included.

Application Considerations

Fabrication stock preparation

Use the material fence and vice to prepare repeatable straight or mitre cuts for downstream fabrication. The adjustable cutting pressure and feed-rate control can be set with the workpiece in mind, provided normal safe operating procedures are followed.

Shared workshop space

The transport handle, carriage, and four wheels make the saw easier to reposition within a workshop. Confirm stable placement, clear access for stock handling, and adequate space around the machine before operation.

Sheet-metal-related tasks

The original product material states that the machine can be used vertically for sheet-metal cutting. Use suitable work support, guarding, and procedures for the material and the task; the product information does not replace site safety requirements.

Selection Guidance

From an engineering perspective, the best fit comes from matching the documented specification to a defined job. The Metal Cutting Band Sawing Machine G5018WA offers a known blade format, defined speed settings, and published round and flat capacities, so a buyer can check compatibility before ordering. If existing fixtures, blade supplies, or local power arrangements are already established, review them early. Small omissions at this stage can add setup work later. The same principle applies to coolant practice and workholding: the equipment features are useful when the surrounding process is ready to use them.

Choose the Metal Cutting Band Sawing Machine G5018WA when its 750 W single-phase drive, 2360 x 20 x 0.9 mm blade, angle-cut arrangement, and published capacities suit the material you need to cut. Its adjustable vice, 45° swivel head, material fence, blade rollers, coolant pump, and mobile base address common shop setup needs without adding unsupported claims about output, precision grade, certification, or automation. For requirements beyond the published data, ask for confirmation before making a purchasing or installation decision.

Operating Preparation

Before operation, inspect the blade, guide adjustment, workholding, coolant arrangement, and the space needed to support incoming and cut stock. Confirm that the material is stable in the vice before starting the cut. When preparing repeated lengths, set the material fence carefully and verify the first cut before continuing. A saw performs best when the operator treats setup as part of the process: match speed and feed to the workpiece, keep the blade path clear, and stop if the work shifts. These practical checks do not change the machine specification, but they help a workshop use the published configuration consistently. For a new installation, check the local electrical arrangement and make sure the machine has a stable working position. Keep routine inspection records according to the shop’s own safety and maintenance procedures, and seek qualified technical advice where a task or local requirement calls for it.

Product Images

Metal Cutting Band Sawing Machine G5018WAMetal Cutting Band Sawing Machine G5018WAMetal Cutting Band Sawing Machine G5018WAMetal Cutting Band Sawing Machine G5018WAMetal Cutting Band Sawing Machine G5018WA

Metal Cutting Band Sawing Machine G5018WA

Request a Quote

Featured Products

product metal cutting band sawing machine g5018wa-1

Get a Free Quote

Our representative will contact you soon.
Email
Mobile/WhatsApp
Name
Company Name
Message
0/1000